| 92.20.1246.990.11.1503 Standard 5 Slewing Ring Bearings | Cg - Geometry Factor:0.202; G2 - Heat Generation Factor (Rib-Roller End):448.6; a - Effective Center Location4:1.4 in; db - Cone Backface Backing Diameter:16.85 in; da - Cone Frontface Backing Diameter:16.46 in; G1 - Heat Generation Factor (Roller-Raceway):2782.9; Design Units:Imperial; C1 - Dynamic Radial Rating (Two-Row, 1 million revolutions)1:425000 lbf; Cone Part Number:EE234156W; Cage Type:Stamped Steel; |
| 161.25.1180.890.11.1503 Standard 5 Slewing Ring Bearings | Dynamic Load Rating C11:8720 kN; Chamfer r1smin2:7.0 mm; Lubrication Groove g:18.0 mm; Inner-Ring Set:300ARXS1845B; Outer-Ring Set:332RXS1846; Angle of Chamfer r1smin:20ยบ; Chamfer rsmin:3.50 mm; Type:RX-1; Lubrication Hole Diameter h:9.0 mm; Weight:287.000 lb; Width B:300.000 mm; Backing Shaft Diameter ds:325.1 mm; DUR/DOR F/E:332.000 mm; O.D. D:420.000 mm; Static Load Rating Co:4140 kN; Number of Lubrication Holes:8; |
| 232.20.0800.503 Type 21/950.2 Standard 5 Slewing Ring Bearings | D:80 mm; T1 - Bearing Width:26.000 mm; G1 - Heat Generation Factor (Roller-Raceway)10:35.7; C0 - Static Radial Rating:119000 N; e - ISO Factor8:0.38; D1 - Flange Outer Diameter:85.000 mm; Bearing Weight:0.6 Kg; d:45.000 mm; Da - Cup Frontface Backing Diameter:79.50 mm; R - Cone Backface To Clear Radius1:1.5 mm; Cone Part Number:X33109; C - Cup Width:20.500 mm; T - Bearing Width to Flange:10.000 mm; |
| 282.30.0975.013 Type 110/1100.2 Standard 5 Slewing Ring Bearings | Snap Ring Width:2.5 mm; Limiting Speed - Oil:8,600 rpm; Factor fo:14.4; b (min):2.7 mm; Dynamic Load Rating:35,000 N; Limiting Speed - Grease:7,100 rpm; Radial Clearance:0.018 to 0.036 mm; Weight:0.463 kg; Enclosure:Snap Ring Groove wit; Snap Ring Outside Diameter:96.5 mm; d:50 mm; a (max):3.3 mm; da (min):57 mm; ra (max):1 mm; Da (max):83 mm; B:20 mm; Cy (max):5.4 mm; Dx (min):98 mm; D:90 mm; Fillet Radius/Chamfer:1.1 mm; |
| 162.25.1320.891.21.1503 Standard 5 Slewing Ring Bearings | Cg - Geometry Factor:0.136; Aa - Cage-Cone Backface Clearance:8.1 mm; C1 - Dynamic Radial Rating (1 million revolutions)6:1110000 N; B - Cone Width:86 mm; da - Cone Frontface Backing Diameter:198 mm; Series:32234; Cage Type:Stamped Steel; G2 - Heat Generation Factor (Rib-Roller End):72.5; DD:255.1 mm; C0 - Static Radial Rating:1750000 N; C90 - Dynamic Radial Rating (90 million revolutions)5:288000 N; |
| 61.25.1155.500.11.1503 Standard 5 Slewing Ring Bearings | ra (max):0.3 mm; Da (max):24 mm; Configuration:Single Row; Fillet Radius/Chamfer:0.3 mm; Dynamic Load Rating:2,630 N; Bore Type:Cylindrical Bore; Radial Clearance:0.011 to 0.025 mm; Weight:0.008 kg; B:5 mm; Static Load Rating:1,570 N; da (min):19 mm; Limiting Speed - Grease:26,000 rpm; Enclosure:Double Shield; Factor fo:16.1; D:26 mm; d:17 mm; |
| 62.25.0955.500.11.1503 Standard 5 Slewing Ring Bearings | Cr - Dynamic Load Rating:0.94 kN; Oil Limiting Speed:13000 rpm; Weight:0.0030 Kg; Outside Diameter D:21.0000 mm; C0r - Static Load Rating:0.58 kN; Grease Limiting Speed:11000 rpm; Clearance:C0 (Normal); Bore Size d:15 mm; Outside Ring Width B:4.000 mm; Features:Open; Radius Rs min:0.200 mm; |
| 91.20.1006.991.21.1503 Standard 5 Slewing Ring Bearings | Bearing:22228K; A2:223 mm; Material :Cast Iron; G:M24; A1:150 mm; H1:150.0 mm; Seal:LO528; Seal Type:Labyrinth; J1:80.0 mm; N:26 mm; Bolt Qty:4; Shaft Diameter d:125 mm; H2:50.0 mm; H:302 mm; Housing Mass:39 Kg; A:205.00 mm; Cage Type:EJ; End Cover2:EC528; C1 Dynamic Load Rating:863; Locknut:KM28; |
| 162.16.0450.891.21.1503 Standard 5 Slewing Ring Bearings | Y - ISO Factor3:1.31; C - Cup Width:1.3750 in; Da - Cup Frontface Backing Diameter:7.83 in; Series:795; e - ISO Factor2:0.46; Cup Part Number:793; Design Units:Imperial; D:8.1250 in; Db - Cup Backface Backing Diameter:7.32 in; Cg - Geometry Factor:0.127; r - Cup Backface To Clear Radius1:0.130 in; |
| 61.25.1055.575.11.1403 Standard 5 Slewing Ring Bearings | G1 - Heat Generation Factor (Roller-Raceway):9384.8; Cone Part Number:EE649239; Ca90 - Dynamic Thrust Rating (90 million revolutions)7:96600 lbf; C90(2) - Dynamic Radial Rating (Two-Row, 90 million revolutions)2:265000 lbf; a - Effective Center Location4:1.24 in; Aa - Cage-Cone Backface Clearance:0.34 in; C1 - Dynamic Radial Rating (Two-Row, 1 million revolutions)1:1020000 lbf; R - Cone Backface To Clear Radius3:0.25 in; |
| 61.25.1255.575.11.1403 Standard 5 Slewing Ring Bearings | K - Factor3:1.45; Y1 - ISO Factor5:1.68; C - Double Cup Width:1.8125 in; Design Units:Imperial; r - Cup Frontface To Clear Radius2:0.03 in; e - ISO Factor4:0.4; Cg - Geometry Factor7:0.0984; Y - ISO Factor1:1.49; Da - Cup Frontface Backing Diameter:4.12 in; D:4.3307 in; Y2 - ISO Factor6:2.5; Series:395; |
| 281.30.1100.013 Type 110/1300.1 Standard 5 Slewing Ring Bearings | C0 - Static Radial Rating:22800 lbf; D:76.2 mm; B - Cone Width:29.997 mm; C - Cup Width:23.813 mm; C90 - Dynamic Radial Rating (90 million revolutions)4:5520 lbf; K - Factor7:1.76; Aa - Cage-Cone Backface Clearance:0.8 mm; Cg - Geometry Factor:0.0697; Design Units:Imperial; Ab - Cage-Cone Frontface Clearance:1.5 mm; db - Cone Backface Backing Diameter:39.12 mm; Series:3100; R - Cone Backface To Clear Radius1:1.270 mm; |
| 60.45.0805.001.11.1504 Standard 5 Slewing Ring Bearings | D1:3.880 in; Taper:1:12; S:0.666 in; Locknut:AN-15; SNW/SNP Assembly Weight:2.54 lb; Bearing Number:22214K; B2:2.286 in; Sleeve:S-15 x 2 3/8; Lockwasher and Lockplates:W-15; Tolerance1:-0.004 in; Series:222K; Diameter d :2 3/8 in; |
| 60.35.0680.000.11.1503 Standard 5 Slewing Ring Bearings | Cage Type:Pin-Type; R - Cone Frontface To Clear Radius1:0.060 in; C1 - Dynamic Radial Rating (Two-Row, 1 million revolutions)4:551000 lbf; B - Double Cone Width:5.4375 in; Aa - Cage-Cone Backface Clearance:0 in; Series:LM767700; T - Bearing Width across Cups:5.4374 in; e - ISO Factor8:0.47; Ab - Cage-Cone Frontface Clearance:0.31 in; Cup Part Number:LM767710; K - Factor7:1.23; Y2 - ISO Factor10:2.12; |
| 61.20.0844.575.01.1403 Standard 5 Slewing Ring Bearings | Bearing Type:Split Cylindrical Re; Bolt Size:4 x M24; Dimension K:3.8 in; Dimension M:6.5 in; Shipping Weight:536 lb; Dimension H2:17.1 in; Note:This product line wa; Series Type:Heavy Series; Shaft Size:130 mm; Ca - Axial Load Rating:11016 lbf; Seal Type:Aluminium Triple Lab; Pillow/Plummer Block Style:Split Cylindrical Ho; Dimension H:7.992 in; Bearing Number:HSM130BR; Dimension J:18.5 in; Cr - Dynamic Load Rating:169281 lbf; |
| 60.25.1255.500.11.1503 Standard 5 Slewing Ring Bearings | Support Type:Two-Bolt Plummer Blo; Dimension L:315 mm; Maximum Speed:3310 rpm; Note:This product line wa; Seal Type:Aluminium Triple Lab; Dimension H2:208 mm; Dimension H:95 mm; Bearing Type:Split Cylindrical Ex; Cr - Dynamic Load Rating:31024 lbf; Cor - Static Load Rating:36194 lbf; Bolt Size:2 x M20; Shaft Size:75 mm; Dimension M:90 mm; Bearing Number:LSM75BX; Dimension J:260 mm; Pillow/Plummer Block Style:Split Cylindrical Ho; |
| No. | Brand | F | J | s | R | B | d | a | b |
| 161.25.1077.890.11.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| 161.20.0710.891.21.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| 162.25.1320.891.21.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| 62.20.0944.575.01.1403 | Standard 5 | - | - | - | - | 16 mm | 50 mm | - | - |
| 232.21.0575.013 Type 21/650.2 | Standard 5 | - | - | - | - | - | - | - | - |
| 12.20.0895.000.11.1504 | Standard 5 | - | - | - | - | - | - | - | - |
| 161.25.0980.891.21.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| 61.25.0980.891.21.1503 | Standard 5 | - | - | - | - | - | 3.2500 in | - | - |
| 232.20.1000.013 Type 21/1200.2 | Standard 5 | - | 320.00 mm | - | - | - | - | - | - |
| 61.20.0710.100.11.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| 61.20.1094.575.01.1403 | Standard 5 | - | - | - | - | 96 mm | - | - | - |
| 60.25.1055.500.11.1503 | Standard 5 | - | - | - | - | 64 mm | 130 mm | - | - |
| 232.20.0500.503 Type 21/650.2 | Standard 5 | - | - | - | - | - | - | - | - |
| 232.20.0600.503 Type 21/750.2 | Standard 5 | - | - | - | - | - | - | - | - |
| 161.20.0630.891.21.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| 231.20.0800.503 Type 21/950.1 | Standard 5 | - | - | - | - | - | - | - | - |
| 60.20.0944.575.01.1403 | Standard 5 | - | - | - | - | - | - | - | - |
| 62.20.0644.575.01.1403 | Standard 5 | - | - | - | - | - | - | - | - |
| 60.20.0844.575.01.1403 | Standard 5 | - | - | - | - | - | - | - | - |
| 62.25.0955.500.11.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| 231.20.1000.013 Type 21/1200.1 | Standard 5 | - | - | - | - | 52.4 mm | 90 mm | - | - |
| 282.30.0975.013 Type 110/1100.2 | Standard 5 | - | - | - | - | 20 mm | 50 mm | - | - |
| 232.20.0800.013 Type 21/950.2 | Standard 5 | - | - | - | - | - | 50 mm | - | - |
| 230.21.0775.013 Type 21/850. | Standard 5 | - | - | - | - | 25 mm | 45 mm | - | - |
| 60.20.0544.575.01.1403 | Standard 5 | - | - | - | - | - | - | - | - |
| 61.20.0450.100.11.1503 | Standard 5 | - | - | - | - | 25 mm | 75 mm | - | - |
| 61.20.0944.575.01.1403 | Standard 5 | - | - | - | - | 24 mm | 100 mm | - | - |
| 232.21.0875.013 Type 21/950.2 | Standard 5 | - | - | - | - | - | 80 mm | - | - |